Rectifying Plan Images - Revision history

WikiSysop: Text replacement - "[[File:" to "[[Image:"

2014-08-15T15:24:44Z

Text replacement - "[[File:" to "[[Image:"

Irina Idelson: /* Rectifying Plan Images */

2012-09-12T13:25:17Z

Rectifying Plan Images

← Older revision		Revision as of 08:25, 12 September 2012
Line 2:		Line 2:

	=== Rectifying Plan Images ===		=== Rectifying Plan Images ===
			(Last Revised 11/15/2006 by Bruce Wacker)

	#Locate the ArcMap icon on your desktop [[File:ArcMap logo.PNG ]]and double click it.		#Locate the ArcMap icon on your desktop [[File:ArcMap logo.PNG ]]and double click it.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T22:42:12Z

Rectifying Plan Images

@@ Line 21: / Line 21: @@
 #[[File:Rectifying plans pic10.PNG|left|thumb|350px|Step 16]]Find the “Georeferencing” tool in the menu and click the down arrow next to it.  Select “Rectify….”.  When the “Save As” dialogue box pops up, type “rectified” in front of the filename and change the file format to “TIF” and click “Save”.  This will save the rectified plan sheet in the same place you saved the original .TIF file on your local hard drive with the same file name except it will have “rectified” in front of it.<br><br><br><br><br><br><br><br><br><br>
 #Copy all the rectified plan files (all extensions) from your personal folder back to the K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet”.<br>
-#Find the “CAMP” icon on your desktop and double click it.  Zoom to the desired area.  Go to “View” on the main menu screen and select “Add Rectified Plan Page”.
+#Find the “CAMP” icon on your desktop and double click it.  Zoom to the desired area.  Go to “View” on the main menu screen and select “Add Rectified Plan Page”.[[File:Rectifying plans pic11.PNG|center]]
+#Browse to the location in K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet” and locate the rectified plan sheet.  Then click “Open”.  This will bring the rectified plan sheet into CAMP.<br>
+#Add the points (signs, light poles, junction boxes, etc.) on the plan sheet just as you would directly on the aerial view.<br>
+#To remove the rectified plan sheet, Click on “View” on the main menu and select “Remove Rectified Plan Page”.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T22:33:35Z

Rectifying Plan Images

@@ Line 18: / Line 18: @@
 #[[File:Rectifying plans pic7.PNG|right|thumb|350px|Step 13]]Locate the “Add Control Points” on the tool bar and click on it.  Pick the first common point from the plan sheet.  Zoom to your bookmark by selecting  “Bookmark” and the bookmark name you saved.  Pick the same common point on the ArcMap aerial view.  This will bring in a small scale plan view anchored at the first point you selected as shown below.[[File:Rectifying plans pic8.PNG|center]]
 #Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box.  Zoom in to the area near the second control point location.  Select the “Add Control Points” button again and select the second control point from the plan sheet view.  ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW.  Use the bookmark feature again and zoom to the ArcMap aerial view.  Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.
-#[[File:Rectifying plans pic9.PNG|right|thumb|350px|Step 15]]On the right hand “Layer Control” column, double click on the layer for the plan sheet.  Select the “Display” tab and set the Transparency to 50%.  This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.
+#[[File:Rectifying plans pic9.PNG|right|thumb|350px|Step 15]]On the right hand “Layer Control” column, double click on the layer for the plan sheet.  Select the “Display” tab and set the Transparency to 50%.  This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.<br><br><br><br><br><br><br><br><br><br><br><br>
+#[[File:Rectifying plans pic10.PNG|left|thumb|350px|Step 16]]Find the “Georeferencing” tool in the menu and click the down arrow next to it.  Select “Rectify….”.  When the “Save As” dialogue box pops up, type “rectified” in front of the filename and change the file format to “TIF” and click “Save”.  This will save the rectified plan sheet in the same place you saved the original .TIF file on your local hard drive with the same file name except it will have “rectified” in front of it.<br><br><br><br><br><br><br><br><br><br>
+#Copy all the rectified plan files (all extensions) from your personal folder back to the K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet”.<br>
+#Find the “CAMP” icon on your desktop and double click it.  Zoom to the desired area.  Go to “View” on the main menu screen and select “Add Rectified Plan Page”.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T22:20:24Z

Rectifying Plan Images

← Older revision		Revision as of 17:20, 11 September 2012
Line 18:		Line 18:
	#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.[[File:Rectifying plans pic8.PNG\|center]]		#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.[[File:Rectifying plans pic8.PNG\|center]]
	#Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.		#Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.
	#On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.		#[[File:Rectifying plans pic9.PNG\|right\|thumb\|350px\|Step 15]]On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T22:09:27Z

Rectifying Plan Images

← Older revision		Revision as of 17:09, 11 September 2012
Line 16:		Line 16:
	#[[File:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.<br><br><br><br><br><br><br><br>		#[[File:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.<br><br><br><br><br><br><br><br>
	#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br><br>		#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br><br>
	#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.		#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.[[File:Rectifying plans pic8.PNG\|center]]
	[[File:Rectifying plans pic8.PNG\|center]]~~<br>~~		#Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.
	Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.
	#On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.		#On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T22:06:47Z

Rectifying Plan Images

← Older revision		Revision as of 17:06, 11 September 2012
Line 18:		Line 18:
	#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.		#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.
	[[File:Rectifying plans pic8.PNG\|center]]<br>		[[File:Rectifying plans pic8.PNG\|center]]<br>
	#Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.		Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.
			#On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.
	~~16.~~ On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T22:05:54Z

Rectifying Plan Images

← Older revision		Revision as of 17:05, 11 September 2012
Line 13:		Line 13:
	#[[File:Rectifying plans pic4.PNG\|right\|thumb\|400px\|Step 8]]Click on the ”Add Data” tool and browse to the location you saved the .TIF file you want to rectify. Highlight the file name and select “Add”. Another screen may come up asking if you want to “Build Pyramids”. If so, click “YES”. Then Click “OK”. This loads the sheet as a layer in the right hand “Layer” column.<br>		#[[File:Rectifying plans pic4.PNG\|right\|thumb\|400px\|Step 8]]Click on the ”Add Data” tool and browse to the location you saved the .TIF file you want to rectify. Highlight the file name and select “Add”. Another screen may come up asking if you want to “Build Pyramids”. If so, click “YES”. Then Click “OK”. This loads the sheet as a layer in the right hand “Layer” column.<br>
	#Find the newly added layer in the right hand “Layer” column and right mouse click on it. Select “Zoom to Layer”. This will take you to the location in space where the layer was brought in at.<br>		#Find the newly added layer in the right hand “Layer” column and right mouse click on it. Select “Zoom to Layer”. This will take you to the location in space where the layer was brought in at.<br>
	#[[File:Rectifying plans pic5.PNG\|left\|thumb\|450px\|Step 10]] Find the “Layer” identification box on the tool bar and make sure it shows the plan sheet name that you want to insert. If not, use the down arrow key at the right end of the box and select the appropriate file.~~<br><br><br>~~<br><br><br><br><br><br><br>		#[[File:Rectifying plans pic5.PNG\|left\|thumb\|450px\|Step 10]] Find the “Layer” identification box on the tool bar and make sure it shows the plan sheet name that you want to insert. If not, use the down arrow key at the right end of the box and select the appropriate file.<br><br><br><br><br><br><br>
	#[[File:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.~~<br><br><br><br>~~<br><br><br><br><br><br><br><br>		#[[File:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.<br><br><br><br><br><br><br><br>
	#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br><br>		#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br><br>
	#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.		#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T21:53:31Z

Rectifying Plan Images

@@ Line 17: / Line 17: @@
 #The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial.  Make sure the two points are located as far apart on the sheet as possible.  You will essentially be stretching the plan sheet across the two selected points.  The use of property corners or surveyed point on an existing curb may be the most accurate if available.  You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier.  Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view.  You can zoom in and out of either view without affecting the procedure.<br><br>
 #[[File:Rectifying plans pic7.PNG|right|thumb|350px|Step 13]]Locate the “Add Control Points” on the tool bar and click on it.  Pick the first common point from the plan sheet.  Zoom to your bookmark by selecting  “Bookmark” and the bookmark name you saved.  Pick the same common point on the ArcMap aerial view.  This will bring in a small scale plan view anchored at the first point you selected as shown below.
+[[File:Rectifying plans pic8.PNG|center]]<br>
+#Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box.  Zoom in to the area near the second control point location.  Select the “Add Control Points” button again and select the second control point from the plan sheet view.  ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW.  Use the bookmark feature again and zoom to the ArcMap aerial view.  Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.
 .	On the right hand “Layer Control” column, double click on the layer for the plan sheet.  Select the “Display” tab and set the Transparency to 50%.  This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.

Irina Idelson: /* Rectifying Plan Images */

2012-09-11T21:44:22Z

Rectifying Plan Images

← Older revision		Revision as of 16:44, 11 September 2012
Line 15:		Line 15:
	#[[File:Rectifying plans pic5.PNG\|left\|thumb\|450px\|Step 10]] Find the “Layer” identification box on the tool bar and make sure it shows the plan sheet name that you want to insert. If not, use the down arrow key at the right end of the box and select the appropriate file.<br><br><br><br><br><br><br><br><br><br>		#[[File:Rectifying plans pic5.PNG\|left\|thumb\|450px\|Step 10]] Find the “Layer” identification box on the tool bar and make sure it shows the plan sheet name that you want to insert. If not, use the down arrow key at the right end of the box and select the appropriate file.<br><br><br><br><br><br><br><br><br><br>
	#[[File:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.<br><br><br><br><br><br><br><br><br><br><br><br>		#[[File:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.<br><br><br><br><br><br><br><br><br><br><br><br>
	#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br>		#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br><br>
	#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.		#[[File:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.

← Older revision		Revision as of 10:24, 15 August 2014
Line 4:		Line 4:
	(Last Revised 11/15/2006 by Bruce Wacker)		(Last Revised 11/15/2006 by Bruce Wacker)

	#Locate the ArcMap icon on your desktop [[~~File~~:ArcMap logo.PNG ]]and double click it.		#Locate the ArcMap icon on your desktop [[Image:ArcMap logo.PNG ]]and double click it.
	#[[~~File~~:Rectifying plans pic1.PNG\|right\|thumb\|450px\|Steps 2 and 3]]Once the application is open, you will see a “Start Up” box. Click the button that says “Add Base Layers”. <br><br><br><br><br><br>		#[[Image:Rectifying plans pic1.PNG\|right\|thumb\|450px\|Steps 2 and 3]]Once the application is open, you will see a “Start Up” box. Click the button that says “Add Base Layers”. <br><br><br><br><br><br>
	#Using the magnifying glass “Zoom In” feature on the tool bar, zoom into the area that you want to insert a rectified plan sheet. Turn on the aerial photograph by selecting the “Add Layers” tool on the tool bar; click on the “+” next to “Air Photos”; place a check in the box next to the “2006 Color 6in Orthophoto”; then click the “Add Selected Layers” button; then click “Close."<br><br><br><br><br><br><br><br>		#Using the magnifying glass “Zoom In” feature on the tool bar, zoom into the area that you want to insert a rectified plan sheet. Turn on the aerial photograph by selecting the “Add Layers” tool on the tool bar; click on the “+” next to “Air Photos”; place a check in the box next to the “2006 Color 6in Orthophoto”; then click the “Add Selected Layers” button; then click “Close."<br><br><br><br><br><br><br><br>
	#[[~~File~~:Rectifying plans pic2.PNG\|right\|thumb\|450px\|Step 4]]Create a bookmark so you can go back to this location quickly during this process. Do this by clicking the down arrow near “Bookmarks” on the top right hand side of the menu bar. Then click “Create”. Name the bookmark by typing in a file name and click “OK”.		#[[Image:Rectifying plans pic2.PNG\|right\|thumb\|450px\|Step 4]]Create a bookmark so you can go back to this location quickly during this process. Do this by clicking the down arrow near “Bookmarks” on the top right hand side of the menu bar. Then click “Create”. Name the bookmark by typing in a file name and click “OK”.
	#Find the Plan Viewer icon on your desktop and double click it. Find the plan sheet that you want to rectify. Note the Project Number as well as the plan sheet number. Then open up Windows Explorer and go to the following directory: K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet”		#Find the Plan Viewer icon on your desktop and double click it. Find the plan sheet that you want to rectify. Note the Project Number as well as the plan sheet number. Then open up Windows Explorer and go to the following directory: K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet”
	#Highlight the correct .TIF file with the desired plan sheet number and copy it to a location on your own C: drive that you will remember.<br><br><br><br><br>		#Highlight the correct .TIF file with the desired plan sheet number and copy it to a location on your own C: drive that you will remember.<br><br><br><br><br>
	#[[~~File~~:Rectifying plans pic3.PNG\|left\|thumb\|600px\|Step 7]]Return to ArcMap. Find “Tools” in the top menu bar and click it. Click “Customize” in the pull down menu and make sure that the box next to “Georeferencing” is checked. Then you can close this dialog box. This will create a sub-menu that you can then “dock” in the top menu bar by clicking and dragging it. <br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>		#[[Image:Rectifying plans pic3.PNG\|left\|thumb\|600px\|Step 7]]Return to ArcMap. Find “Tools” in the top menu bar and click it. Click “Customize” in the pull down menu and make sure that the box next to “Georeferencing” is checked. Then you can close this dialog box. This will create a sub-menu that you can then “dock” in the top menu bar by clicking and dragging it. <br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br><br>
	#[[~~File~~:Rectifying plans pic4.PNG\|right\|thumb\|400px\|Step 8]]Click on the ”Add Data” tool and browse to the location you saved the .TIF file you want to rectify. Highlight the file name and select “Add”. Another screen may come up asking if you want to “Build Pyramids”. If so, click “YES”. Then Click “OK”. This loads the sheet as a layer in the right hand “Layer” column.<br>		#[[Image:Rectifying plans pic4.PNG\|right\|thumb\|400px\|Step 8]]Click on the ”Add Data” tool and browse to the location you saved the .TIF file you want to rectify. Highlight the file name and select “Add”. Another screen may come up asking if you want to “Build Pyramids”. If so, click “YES”. Then Click “OK”. This loads the sheet as a layer in the right hand “Layer” column.<br>
	#Find the newly added layer in the right hand “Layer” column and right mouse click on it. Select “Zoom to Layer”. This will take you to the location in space where the layer was brought in at.<br>		#Find the newly added layer in the right hand “Layer” column and right mouse click on it. Select “Zoom to Layer”. This will take you to the location in space where the layer was brought in at.<br>
	#[[~~File~~:Rectifying plans pic5.PNG\|left\|thumb\|450px\|Step 10]] Find the “Layer” identification box on the tool bar and make sure it shows the plan sheet name that you want to insert. If not, use the down arrow key at the right end of the box and select the appropriate file.<br><br><br><br><br><br><br>		#[[Image:Rectifying plans pic5.PNG\|left\|thumb\|450px\|Step 10]] Find the “Layer” identification box on the tool bar and make sure it shows the plan sheet name that you want to insert. If not, use the down arrow key at the right end of the box and select the appropriate file.<br><br><br><br><br><br><br>
	#[[~~File~~:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.<br><br><br><br><br><br><br><br>		#[[Image:Rectifying plans pic6.PNG\|right\|thumb\|350px\|Step 11]] Make sure the “Rotate Data Frame” angle is set to 0. The default is 358 so everything appears vertical and horizontal. However, the next process will not function unless you reset the angle to 0.<br><br><br><br><br><br><br><br>
	#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br><br>		#The process of rectifying a drawing to the aerial in ArcMap requires that you select two points that are readily identifiable on both the plan sheet and the ArcMap application aerial. Make sure the two points are located as far apart on the sheet as possible. You will essentially be stretching the plan sheet across the two selected points. The use of property corners or surveyed point on an existing curb may be the most accurate if available. You can toggle between the plan view and the aerial view by selecting “View”, then “Bookmarks”, then the bookmark name that you saved earlier. Right click the layer name on the left hand layer control box and select “Zoom to Layer” to get back to the plan view. You can zoom in and out of either view without affecting the procedure.<br><br>
	#[[~~File~~:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.[[~~File~~:Rectifying plans pic8.PNG\|center]]		#[[Image:Rectifying plans pic7.PNG\|right\|thumb\|350px\|Step 13]]Locate the “Add Control Points” on the tool bar and click on it. Pick the first common point from the plan sheet. Zoom to your bookmark by selecting “Bookmark” and the bookmark name you saved. Pick the same common point on the ArcMap aerial view. This will bring in a small scale plan view anchored at the first point you selected as shown below.[[Image:Rectifying plans pic8.PNG\|center]]
	#Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.		#Zoom back to the plan sheet layer again by right clicking on the layer name on the right side of the ArcMap layer box. Zoom in to the area near the second control point location. Select the “Add Control Points” button again and select the second control point from the plan sheet view. ALWAYS SELECT FROM THE PLAN SHEET VIEW FIRST THEN THE ARCMAP AERIAL VIEW. Use the bookmark feature again and zoom to the ArcMap aerial view. Select the common second control point from the ArcMap aerial view. This will stretch the plan sheet to full size in real space.
	#[[~~File~~:Rectifying plans pic9.PNG\|right\|thumb\|350px\|Step 15]]On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.<br><br><br><br><br><br><br><br><br><br><br><br>		#[[Image:Rectifying plans pic9.PNG\|right\|thumb\|350px\|Step 15]]On the right hand “Layer Control” column, double click on the layer for the plan sheet. Select the “Display” tab and set the Transparency to 50%. This will allow you to see through the plan sheet to see if the rest of the visible lines match with the aerial lines.<br><br><br><br><br><br><br><br><br><br><br><br>
	#[[~~File~~:Rectifying plans pic10.PNG\|left\|thumb\|350px\|Step 16]]Find the “Georeferencing” tool in the menu and click the down arrow next to it. Select “Rectify….”. When the “Save As” dialogue box pops up, type “rectified” in front of the filename and change the file format to “TIF” and click “Save”. This will save the rectified plan sheet in the same place you saved the original .TIF file on your local hard drive with the same file name except it will have “rectified” in front of it.<br><br><br><br><br><br><br><br><br><br>		#[[Image:Rectifying plans pic10.PNG\|left\|thumb\|350px\|Step 16]]Find the “Georeferencing” tool in the menu and click the down arrow next to it. Select “Rectify….”. When the “Save As” dialogue box pops up, type “rectified” in front of the filename and change the file format to “TIF” and click “Save”. This will save the rectified plan sheet in the same place you saved the original .TIF file on your local hard drive with the same file name except it will have “rectified” in front of it.<br><br><br><br><br><br><br><br><br><br>
	#Copy all the rectified plan files (all extensions) from your personal folder back to the K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet”.<br>		#Copy all the rectified plan files (all extensions) from your personal folder back to the K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet”.<br>
	#Find the “CAMP” icon on your desktop and double click it. Zoom to the desired area. Go to “View” on the main menu screen and select “Add Rectified Plan Page”.[[~~File~~:Rectifying plans pic11.PNG\|center]]		#Find the “CAMP” icon on your desktop and double click it. Zoom to the desired area. Go to “View” on the main menu screen and select “Add Rectified Plan Page”.[[Image:Rectifying plans pic11.PNG\|center]]
	#Browse to the location in K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet” and locate the rectified plan sheet. Then click “Open”. This will bring the rectified plan sheet into CAMP.<br>		#Browse to the location in K:\Library\Plans\images\”Your Project Number”\”Desired Plan Sheet” and locate the rectified plan sheet. Then click “Open”. This will bring the rectified plan sheet into CAMP.<br>
	#Add the points (signs, light poles, junction boxes, etc.) on the plan sheet just as you would directly on the aerial view.<br>		#Add the points (signs, light poles, junction boxes, etc.) on the plan sheet just as you would directly on the aerial view.<br>
	#To remove the rectified plan sheet, Click on “View” on the main menu and select “Remove Rectified Plan Page”.		#To remove the rectified plan sheet, Click on “View” on the main menu and select “Remove Rectified Plan Page”.